How to Insulate a Metal Garage Door?

Many garage doors are “Non-Insulated” and allow a great loss of heating and cooling if your garage is attached to your house.

Insulating the interior of the garage door is easy and provides a substantial cost savings on your energy bills. To see if your garage door does have insulation already installed, with the garage door in a fully closed position:

Garage Door Interior Closed
Garage Door Interior Closed

If the garage does is “Non Insulated” you will be able to see the back of the metal panels, If the garage door is already insulated the interior side of the door will look like the image below:

Garage Door Interior Closed Non-Insulated
Garage Door Interior Closed Non-Insulated

If you determine that your garage door is not insulated and wish to keep the temperatures more comfortable within your garage and save money on utility bills keep reading.
This is a very easy project which can be done in a few hours, Just follow the instructions and you will be impressed on the difference this project will make.


  • Tape Measure
  • Utility knife and extra blades
  • Straight edge 3’ft – 4’ft long (A solid piece of wood with a straight edge or yard stick)
  • Safety Glasses


  • ¾” or 1” foil faced foam insulation (Measure garage door opening – Height x width = SF)
  • Example – If your garage door opening is 7’ x 8’ it would require 56 Square Feet of insulation
  • 1-2 rolls of 1-1/2” aluminum foil metal tape or duct tape – The metal tape is the best

How to install the insulation:

Garage Door Install
Garage Door Install
  1. Measure the opening as shown above (Example is 1’3 5/8” Tall x 3’9 ½” wide) * Note your measurements may vary depending on style and size of door
  2. Add 1” to the height of the opening (Example 1’3 5/8” +1” = 1’4 5.8”) This will allow the insulation to be held in place by the hinged frame rails
  3. Place the insulation board on a flat surface such as your drive way. Mark the measurements on the foil side of the insulation and gently cut the insulation board to the proper size
  4. Place the piece you cut into the lower hinge rail and then gently bend the insulation into the top hinge rail and release
  5. Complete the job by doing the same thing to each panel and installing the foil metal tape or duct tape around all 4 side of each panel your installed the insulation board in.
  6. CAUTION: Do not allow the tape to cover the joint in the hinge rail or interfere with the rollers on either side of the door.
  7. After complete open the garage door and make sure that nothing binds or comes into contact with other surfaces or moving parts
Garage Door Completed
Garage Door Completed

How to Install a Garage Door Opener?

Garage Door Opener
Garage Door Opener

Garage door openers have become an important part of life today. Garage door opening devices offers safety and convenience for anyone. Some garage door openers have an external keypad that can help you enter you garage in the case that you do not have your remote. A garage door opener can hold a garage door shut, which can add to the overall safety of your house. In addition, all new garage door-opening devices use safety sensors to ensure that the garage door does not close on a human or animal.

The garage door opener installation steps are easy. However, installation steps vary between manufacturers. However, many steps are universal. This article aims to inform you on the steps to install a garage door opener. Keep in mind that these are general instructions. In any installation, you should follow the manufacturer’s instruction manual.

Before beginning, you should ensure that you have a power receptacle with a proper ground and GFCI. It is important to ensure that the door is functioning properly prior to installing the garage door opener. Some garage doors use springs, and should be checked for proper tension.

First, ensure that the T-rail pieces are arranged in the proper manner. Some T-rails have arrows on them. It is important to ensure that all of these arrows are pointed in the same direction. You should bolt them together securely. Next, ensure that the idler pulley is aligned and bolt it in. Next, slide the trolley into the rails, this will allow you to connect the opener unit. Next, use a screwdriver to hold the trolley in its place. After accomplishing this, you should attach the drive chain onto the provided trolley.

Next, you should open the door to find out how high the door travels over the tracks. To be safe, you should add two inches to the measurement. Mark this measurement above the door. You should then find out where the center of the door is located. Mark the center of the door with a marker. You will mount the header bracket on this point. It may be necessary to attach a few 2x4s across the studs if your location is not over a stud. After ensuring that you have a sturdy mounting location, it is safe to mount the bracket.

Now, you should close your garage door. The idler pulley should be attached to the header bracket. The assembly should now be placed on a stepladder. Next, open the door and raise the rail above the door. Then, attach the bracket to the ceiling with screws. You should make sure that the opening unit is stable by ensuring that the brackets are crossed. You may now install the controls. You should attach your opening module near the door that allows you to enter the garage. You should now install the electronic sensors. These sensors are extremely important because they can keep your child, car, or pet safe in the event of an accidental closing of the garage door. You should use staples that are insulated, and should run the wires 20” along the frame. Then, connect the proper wires to the opening unit.

The final step is to attach the bracket. You must ensure that the garage door is parallel to the rail. Then, ensure that the door is closed well. Then, attach the curved arm to the bracket.

After performing these steps, you may plug in the opening unit. Test the unit by pressing the open button. You may fine-tune your opener using the onboard controls. If everything works properly, you are finished! If you followed these steps, your installation should’ve gone great.

How to Choose Garage Organizers?

Garage Organizer
Garage Organizer

If your garage is overloaded so much that there is no room to park the car inside chances are you could really benefit from garage organizer systems. When you open the garage door and it looks like there is a perpetual garage sale ongoing it is time for a garage makeover.

For under $500 you can pick up many accessories and storage helpers to do your garage makeover. It is important to free up floor space so the garage can again regain its main purpose of vehicle protection. Begin by sorting through all the items in the room, even if it takes you a week or longer. Gather together a trash can and a couple boxes and be ruthless in sorting.

Put anything that is broken, junk or no longer needed into either the trash or a box designed for selling items, recycling items or donations to others. When you are finished, set the trash out on trash pickup day. Take the items no longer wanted but still in okay shape out for recycling or reselling. Have that garage sale, but get rid of the two categories marked as junk or resell. Make deals or give away items because you want to get rid of it, not keep it. Another box is for items you want to keep and that are useful. Set this box or boxes aside momentarily; set them in the center of the now empty room.

At this point you should be able to see all the walls. If they need attention, repair or painting, do it now. Next go in search of a garage organizer and accessories. Shop at the local improvement store or online for the best ideas and prices. Many items are just a few dollars like hoods and small bins. Rubber tubs with tops are only about $5 each and they can be stacked high. Tubs and bins with covers help keep water and insects out of your stored items.

Consider shelving units, cabinets and wall boards that will accept hooks and peg hangars. There is special pegboard made for this purpose, and slat wall materials that will accept various types of storage accessories. Wide and tall shelving units can hold an amazing amount of clutter in a neatly organized manner. Space out shelves so that there is room for larger tubs on the bottom and smaller ones up higher. Use see through bins for some items and open front bin storage drawers for others. Hanging drawer storage units go onto wall systems or they can be placed atop cabinets.

On the peg or slat walls you hang hooks, shelves, and baskets or bins for items that need to be visible. Tools are stored in easy reach on these walls or they can be stored in their own rolling tool cart. Large lawn and garden tools need some storage areas that have height. They can be hung on the wall units or put into a tall cabinet or closet area. Keep them near to the front of the room so they are more likely to be used. Baskets and bins are great for sports items like soccer and basket balls. Get a small step stool so you can reach higher items as you go upwards in using your space. Purchase a roll up unit to hold the hose or hang the rolled up hose on hooks rather than piled on the floor.

For ceiling storage there are lift up ceiling units that are easy to use. Use all available non-floor space on walls and above the room. An open rafter ceiling can still be used for some types of storage and hooks. Keep bulkier items like buckets, baskets and bikes stored where they will not be in the way. Use cabinets with doors to hide objects and keep the room looking neat and clean. If you have seasonal items keep them either up in the ceiling space storage or labeled and stored near the back of the room.

Plan the garage organization so you have a good workspace because there is always something that needs attention around a home. Use LED strip lights if needed in dark corners. Create a desk area or work station that is well lit and comfortable to use and include a comfortable chair. Be sure to have a trash container near the desk and a large trash can near the front of the garage or just outside it. Dispose of items instead of just tossing them in a pile inside the garage for later pick up that sometimes does not happen quickly.

Now that your garage is organized put the items from the boxes you set in the center of the room onto their designated storage areas. Break down the cardboard boxes and take the cardboard to your local recycling center for disposal. Return and park the vehicle in the now clean and organized garage.

Garage organizing is almost like adding another large room to the home. Garage space is valuable space but many times it is used for a messy and unmanageable pile up of things. Many people cannot even remember what is in the garage or where items might be in the room. With a garage organization systems and ample storage accessories the vehicle can once again enter the space with plenty of room all around it. Protect the vehicle and give yourself extra open space for projects by using garage storage systems.

How to Choose Garage Floor Covering?

Garage floors are very different than any other floors within the household. Because garages are used for utilities and usually have cars parked within them, they are susceptible to damage. Protection of these floors is key because of the chemicals that come in contact with them. Some of these chemicals that are detrimental to the floor are: oil, antifreeze, battery acid, salt, brake fluid, gasoline, air conditioner freon, and transmission fluid.

Not protecting a garage floor will lead to deterioration of the floor and unexpected expenses down the road. It is a good idea to protect the floor right away using garage floor covering so that these expenses are prevented. Not only do chemicals ruin the floor of the garage, they also present a danger to people when walking; a chemical spill (depending on the chemical) can make the floor very slippery and therefore dangerous to the family and/or visitors walking through the garage.

Homeowners have several options in protecting a garage floor. Some are better than others in the way of longevity and strength against certain chemicals. The options in protecting a garage floor from damage are:

garage floor covering

Paint – This is the least expensive of garage floor coverings but the least effective. Although you get to choose any color that adds to the aesthetics of your garage, the protection is not nearly as strong as the others. In addition, those who choose to go with a layer of paint must repaint every so often to keep a layer of protection on the garage floor. The cost for painting the garage floor is minimal and usually done by the homeowner. So, the overall cost will be anywhere from $20 to $50 for the paint.

Epoxy Coating – This is one of the most commonly used method is to paint the floor with. Epoxy garage floor covering is great for sealing in the floor’s porous surface so that chemical spills do not seep into the floor and damage it. This method is somewhat difficult and takes more time than other methods. Though if done properly becomes a much more durable method than paint. A good layer of epoxy will give a garage a brilliant shine like a sportscar showroom. Before applying the epoxy, one must prep the surface. Not preparing the surface properly will compromise the protection significantly. Also, the application must be thorough enough so that subsequent applications are not needed. Furthermore, the application of epoxy must be done with adequate ventilation. If one chooses to have a professional apply the epoxy instead of doing it his/herself, they can expect to pay anywhere from $5 to $15 per square foot; this does not include the cost of the materials.

PVC or Vinyl Mats – These are by far the easiest to clean. Also, since the mats are made of PVC, they let nothing pass through the mat. These mats come in square mat types as well as roll out types. Roll out types can be shaped, formed, and designed with a variety of colors and designs to add to the aesthetics of your garage. Most of the time, these come in roll-out type strips or square pieces that need to be installed. Usually they are quite easy to install and do not require a professional. Homeowners can expect to pay anywhere from $300 to $1,000 to cover the entire garage. The price for these roll-out type mats depend on the size of the garage.

Garage Tiles – Tiles for the garage are probably the best but most expensive method to go with. Garage tiles are no different than home tiles; the difference is in the adhesive used to lay them down. Like epoxy coating, the floor must be perfectly cleaned and prepared before application. Garage tiles are great because they look good and provide a non-porous surface so that chemical spills can be cleaned up easily. And, since the tiles are not porous, spills will not damage the tiles as long as the spill is cleaned up right away. If the homeowner chooses to do this project on his/her own, they are looking at anywhere from $200 to $1,200 for materials depending on the size of the garage. If a professional installs garage tiles, the price can cost anywhere from $1,200 to $8,000 depending on the size of the garage.

Parking Mats – These mats, as specified in the name, are simple mats that you park over. Although they just protect the area underneath the car, they are very sturdy. And, like all over mat-type methods, they can be easily removed for cleaning. Parking mats are perfect for those who do not use the garage for anything else but parking. However, if any members of the household use the garage for car repairs or jobs that require the use of chemicals, parking mats would not provide the coverage necessary to protect the floor. Because parking mats require no installation, the cost is for the materials only. Homeowners can expect to pay anywhere from $30 to $300 per garage floor covering mat depending on what material and/or design they choose.

Some garage floor coverings are permanent and some are not. Flat mats and roll-out mats can be taken up as easy they are put down. However, most of these methods leave areas for corrosive chemicals to seep through. However, some prefer these methods because mats can be taken up and cleaned thus reducing the amount of dirt that can be tracked into the home. Another benefit of mats is that they can cover unsightly stains. Additionally, mats, unlike coatings do not require the work of application; most can be simply rolled or placed onto the surface. Although some methods are preferred over others, any floor covering for the garage is better than no covering at all. Most homeowners don’t even consider this fact and find themselves having to repair the garage floor before selling or renting the home. It is always best to prevent this situation by employing a garage floor covering no matter what type of covering one chooses.

How Much Do Prefabricated Garages Cost?

Prefabricated Garage
Prefabricated Garage

Prefabricated garages are highly desirable when one wishes to install a fairly cost-effective and simple garage structure for their home. Often, a great deal of time will be saved going with this particular method. Since there are multiple designs to choose from, the sky is definitely the limit as to what one could conceivably end up with. Many considerations must be made, from materials of the structure itself to whether hiring a professional will be required. Accordingly, this article will cover each of the aforementioned steps in detail. Hopefully, after all is said and done, what you will be left with is an enjoyable, sturdy structure to add value and usefulness to your home.

Which Prefabricated Garage Kit Should Be Purchased

When deciding upon which kit to purchase, it is first important for you to decide what material you want the structure to be made of. Is wood more desirable for you? What is the weather like where the garage will be erected? How many doors are desired? These are all questions that should be asked before deciding which kit to purchase. Having said this, here are several reputable manufacturers of premade garage structures, including their contact information and how long they have been in business:

  • Garage Kit Packages by APM P.O. Box 310 46 Gettysburg Street Arendtsville, PA 17303 1-888-261-2488 (telephone) 1-717-677-8102 (facsimile) Years in Business: Forty-Six
  • Summerwood Products 735 Progress Ave. Toronto, ON Canada M1H 2W7 1-866 519-4634 Years in Business: Twenty-One
  • Prefabricated Garage Kits, Inc. A division of ClickShops, Inc 509 N. 5th Ave. Ste H Sandpoint, ID 83864 1-208-263-7756 ex. 430 1-208-255-5768 (facsimile) Years in Business: Six
  • Carports and More 10523 Fair Oaks Blvd., Ste 325 Fair Oaks CA 95628 1-877-275-7048 1-888-376-4428 (facsimile) Years in Business: Six

Average Garage Kit Costs

Depending upon whether you desire wood prefabricated garage kit or a structure made from metal, the prices obviously will fluctuate. In general, you can expect to pay in the neighborhood of $14,000 for a premade wood garage and $4,900 and above if the structure is made from steel or other non-wood materials.

How Easy Will It Be To Install It Myself?

There are many premade garage kits available that are specifically designed for the novice to install. One can completely erect their garage often within just one day. Since the structure comes already constructed, it is quite easy for one to do themselves. Where you may need a contractor’s help is if you choose to have electricity for your garage structure. Should you desire this, you will likely need to hire an individual to do the proper wiring which will be required.

Finding A Contractor

The MOST important aspect of deciding upon a contractor is that this individual is both licensed and insured. Countless home improvements are marred with horrid memories by inept individuals who have neither the skill nor the licensure to work on such a project. Therefore, many headaches can be avoided if one secures personal references before hiring this person. An excellent resource for this would be to contact the National Association of the Remodeling Industry. They should be able to provide you with a list of members in your particular area. Another resource is often a local building inspector, who should be familiar with local contractors who meet the appropriate building code procedures.

In order to pick the right contractor for this type of project, it is best to ask the prospective worker the following questions:

  1. What projects are they most skilled in working with?
  2. Have they got appropriate references to show you from past clientele?
  3. If they work with subcontractors, how long have they been doing so?
  4. Do they have multiple projects they work on at the same time? This is crucial in that problems may occur with the project. You do not want to encounter difficulties reaching your contractor because he or she is too swamped to get back to you.
  5. Are they licensed, bonded and insured?

Once these questions have been asked, you will generally be able to get a sense of this person’s reliability and professionalism. But do not rely only on the answers the individual provides to you. If at all possible, and if he or she is currently working on a project, ask to visit the worksite itself. This will give you an excellent picture of your prospective contractor in action.

Average Contractor and Electrical Specialist Costs

Average contractor rates fluctuate considerably depending upon location, but a starting point would be roughly $27.00 per hour for a certified construction contractor and $25.00 per hour should you require the help of a certified electrical specialist as well.

Is A Premade Garage The Way To Go

Garage structures will often add monetary value to a home, so they are quite a valuable addition should one not already exist or if a rebuilt garage is desired. Given that prefabricated garage kits come mostly preassembled, depending if one is fairly adept with a hammer, screwdriver and ladder, self-installation is an easy route to take. If hiring a professional to install the kit is desired, there are many different individuals to choose from. Whichever route is taken, proper research is suggested before proceeding. When these steps are fully undertaken, the result will most likely be very successful.